- Mototrbo cps error 1060 driver#
- Mototrbo cps error 1060 software#
- Mototrbo cps error 1060 code#
- Mototrbo cps error 1060 license#
- Mototrbo cps error 1060 windows 7#
By default the IP address of the radio is 192.168.10.1. Since the radio is seen as a network connection by Windows, you can ping it.
![mototrbo cps error 1060 mototrbo cps error 1060](https://i0.wp.com/mbars.co.uk/wp-content/uploads/2014/10/expert-mode.jpg)
USB 3.0 ports will have blue insulator material - USB 2.0 ports are black.Ĭan you ping the radio. These are known to be quirky so try a USB 2.0 port to eliminate this as a cause.
Mototrbo cps error 1060 driver#
If the radio appears in the Unknown Devices tree in Windows Device Manager, then you need to make sure the CPS is installed on this PC or, at the very least, the driver files.Īre you using a USB 3.0 port. In Windows Device Manager the radio will show up as a network adapter.ĭid the driver load. In Network Connections the radio will show up as a network connection with an IP address. Once the RNDIS driver is loaded, have a look in your Network Connections and in Windows Device Manager. Wait a few seconds before pressing the read button.Ĭan you see the radio in Windows.
![mototrbo cps error 1060 mototrbo cps error 1060](https://2.bp.blogspot.com/-n6ym4m5lAfE/WK_1qeE2ryI/AAAAAAAACXI/pdDudqmJwhkFY4lu5yTlNUtkWhmdyh_awCPcBGAYYCw/s1600/MOT_Build-01.png)
The RNDIS driver takes a few seconds to load depending on how fast/cluttered your PC is.
Mototrbo cps error 1060 windows 7#
Here is a video showing the sounds that Windows 7 will produce. When the radio is plugged in to the PC, a USB RNDIS driver gets loaded. Windows will notify you when the radio is connected and disconnected. Even I get caught out by this more often than I care to admit.ĭoes Windows "see" the radio. You will either need to get a PMKN4012B or modify (caveat emptor) your cable to support this (details can be found on the internet). On that point, if you have a PMKN4012A and a DP4000 series radio, this combination wont work. So if you plug in the cable, Windows will not see it as a device. The thick round thing on the cable is just a RF choke. There is no intelligence in the programming cable. An old toothbrush with a little contact cleaner or methanol will make sure those contact are clean. Sometimes dirt and other interesting things can get onto the accessory connector terminals - especially portables. Is the programming cable really plugged into the PC and connected to the radio. There are a number of causes for this and many of them can be solved with a few simple checks.Ĭheck the connections. It basically means that the radio did not respond. Please note that this bulletin is informational only and No labor Warranty is intended or implied.If you've ever read a MOTOTRBO radio, you might have come across this error message.
Mototrbo cps error 1060 code#
If a code plug has become corrupted there are no actions a dealer or customer can take to restore the radio to an operational state and the radio must be returned for service to the regional depot for repair. When programming thru the CPS, wait for the “Writing the radio was successful.” message as shown in Figure 3 before disconnecting the programming cable from the radio. Personal Digital Assistant synchronizing tools or other radio programming software) that could access the communication ports before launching the CPS. Be sure to quit any other applications (i.e. Verify that all connections to the RIB and computer are correct and secure before programming any radios. Make sure the programming cable is fully seated into the radio before programming. It is recommended that a fully charged battery or a Shop Battery Eliminator (Motorola Part Number 0180305K08) be used during the programming sessions.
Attempts to read a radio after the corruption has occurred will result in the error messages as shown
Mototrbo cps error 1060 software#
New batteries are not shipped fully charged.Ī) Battery’s require a 16 hour initial charge to assure proper cell balance.ī) A new battery may have enough energy to support initial read operations by the CPS but writing and cloning operations require more energy and the uncharged battery may not supply the necessary voltage and current required to complete the programming operation successfully, thus causing code plug corruption.ģ) Interruptions that result in code plug corruption can also be caused by loose, intermittent or prematurely broken connections between the computer and the radio during a write or clone operation.Ĥ) Interruptions that can cause corruption can also come from other software applications that reconfigure the communication port or attempt to communicate via the same communication port as the CPS during a programming session. The interruption can occur due to several factors:ġ) Noise on the RIB cable between the PC and the radio causes errors in the CPS programming dataĢ) Using a weak or uncharged battery during the programming session. The code plug can become corrupted if the programming is interrupted prior to the program operation being completed. Reading a radio after unsuccessfully writing to or cloning to the radio. Please note that Amateur Radio Software does not sell any Motorola Radio Software online.ĬPS RVN4191 generates “Error # 2417 Codeplug version not supported” message as shown in Figure 1 or “Error # 2436 Codeplug is corrupted.Ĭontact Customer Service Center.” as shown in Figure 2 when
Mototrbo cps error 1060 license#
For customer who have a valid CPS license from Motorola.